Tín hiệu Amp hoặc Vol; Vỏ máy đạt NEMA 4X
SERIES BTT là cảm biến nhiệt độ có tín hiệu suất ra giống với các cảm biến thermistor TE và RTD phù hợp với các hệ thống quản lý toà nhà. Cảm biến này có thể dung theo dõi nhiệt độ trong ống gió hoặc ống nước. Có thể gắn trên ống gió, ống nước, ngoài trời. Với các model gắn ống gió, ống nước đầu dò có thể dài từ 2.5” đến 18”. Model OSA có thể đặt thêm bộ phận chống bức xạ để có thể hoặt động trực tiếp dưới ánh nắng.
Temperature Sensor: | Pt1000 RTD. |
Range: | -40 to 140°F (-40 to 60°C). |
Temperature Limits: | -40 to 140°F (-40 to 60°C). |
Accuracy: | Voltage: 0 to 60°C: ±0.5°C; -40 to 0: ±1.0°C; Current: -20 to 50°C: ±0.5°C; -40 to -20°C and 50 to 60°C: ±0.75°C. |
Response Time: | 100 ms. |
Wetted Materials: | All models: 304 SS (probe), polycarbonate (housing); Duct and immersion models: Neoprene (gasket); Outside air models: Nylon (insert), silicone (O-ring). |
Process Connection | 1/2″ NPT (immersion models only). |
Electrical Connection: | Removable terminal block, knocks out for conduit fitting. |
Conduit Connection: | 1/2″ NPT. |
Probe Lengths: | 2.5 to 18″ (depending on configuration). |
Power Requirements: | 13 to 36 VDC. |
Output Signal: | 4 to 20 mA or 0 to 10 VDC (depending on model). |
Enclosure Rating: | NEMA 4X (IP66) (immersions models require thermowell). |
Weight: | 5.11 oz, 145 g (duct/immersion); 8.4 oz (238 g) (OSA without radiation shield); 1 lb 7.4 oz (663.4 g) (OSA with radiation shield). |
Agency Approvals: | CE |
Tài liệu kỹ thuật:
Catalog :
CE
[:vi]SERIES DH3 là bộ điều khiển chênh áp suất kỹ thuật số có màn hình hiện thị 3-trong-1, có relay, tín hiệu suất ra dạng dòng, tất cả nằm trong vỏ Photohelic. Bao gồm 3 chức năng giúp giảm các thiết đo khác, giảm chi phí lắp đặt và thời gian. Bộ DH3 thích hợp để đo áp suất, vận tốc gió và các ứng dụng lưu lượng, có độ chính xác 1% toàn dãy và thậm chí cho các thang đo thấp 0.25”w.c đến 2.5” w.c. Với thang đo 5”w.c độ chính xác 0.5%. Đo 2 chiều cũng có sẵn.
Bộ điều khiển DH3 Digihelic® cho phép chọn đo áp suất, vận tốc hay lưu lượng với nhiều đơn vi đo. 2 replay có thể điều chỉnh được deadband với tính hiệu xuất là 4-20mA.
Lập trình dễ dàng nhờ vào 5 phím và menu đơn giản: bảo mật; lựa chọn áp suất, vận tốc gió hay lưu lượng; lựa chọn đơn vị đo; cài đặt set point, báo động cho mức cao/ thấp; tự động hoặc reset bằng tay; xem các thông số cao nhất/thấp nhất;tín hiệu suất4-20mA thích hợp cho các ứng dụng.
Tham khảo thêm SERIES AT2DH3 nếu cần chứng nhận ATEX[:en]The SERIES DH3 Digihelic® Differential Pressure Controller is a 3-in-1 instrument possessing a digital display gage, control relay switches, and a transmitter with current output all packed in the popular Photohelic® gage style housing. Combining these 3 features allows the reduction of several instruments with one product, saving inventory, installation time and money. The Digihelic® controller is the ideal instrument for pressure, velocity and flow applications, achieving a 1% full scale accuracy on ranges down to the extremely low 0.25″ w.c. to 2.5″ w.c. full scale. Ranges of 5″ w.c. and greater maintain 0.5% F.S. accuracy. Bi-directional ranges are also available.
The Series DH3 Digihelic® controller allows the selection of pressure, velocity or volumetric flow operation in several commonly used engineering units. 2 SPDT control relays with adjustable deadbands are provided along with a scalable 4-20 mA process output.
Programming is easy using the menu key to access 5 simplified menus which provide access to: security level; selection of pressure, velocity or flow operation; selection of engineering units; K-factor for use with flow sensors; rectangular or circular duct for inputting area in flow applications; set point control or set point and alarm operation; alarm operation as a high, low or high/low alarm; automatic or manual alarm reset; alarm delay; view peak and valley process reading; digital damping for smoothing erratic process applications; scaling the 4-20 mA process output to fit your applications range and field calibration.
Please see SERIES AT2DH3 for ATEX approved.[:]
[:vi]Bộ SERIES TE-E/N Wall Mount Temperature Sensor đáp ứng chi phí thấp với bất kỳ hệ thống tòa nhà nào. Với lỗ thông gió lớn, cảm biến đo chính xác nhiệt độ môi trường xung quanh trong phòng khách sạn hoặc tòa nhà văn phòng.[:en]The SERIES TE-E/N Wall Mount Temperature Sensor provides a low cost temperature input for any building management system. With large vents in the housing for proper air flow, the sensor accurately measures the ambient temperature in hotel rooms or office buildings. Multiple mounting holes on the wall plate allow for mounting to numerous surfaces.[:]
[:vi]Ta có thể Lập trình, ghi dữ liệu, phân tích, và kiểm soát lưu lượng của nhiều loại khí bằng cảm biến DMF Digital Mass Flow Controller. Bộ điều khiển được thiết kế với ống cảm biến với các lỗ hẹp để đảm bảo chế độ chảy tầng nhằm cho kết quả chính xác và lặp lại. Cảm biến DMF không bị ảnh hưởng khi thay đổi nhiệt độ và áp suất.
Bộ điều khiển có thể được lập trình để thực hiện nhiều chức năng gồm có lưu lượng cài đặt, đo tổng lượng nước, dừng đo tổng lượng nước, bắt đầu đo tổng lượng nước tại một lưu lượng cài đặt, dừng và cài đặt trước tổng lượng nước, auto zero, và hơn nữa. Tính năng auto zero dùng mạch cân bằng cho phép loại trừ sai lệch khi hiệu chỉnh zero và span. Ngoài ra, bộ điều khiển Series DMF còn có 2 tiếp điểm dùng để điểu khiển bơm van, hoặc các thiết bị vận hành.
Series DMF có chức năng tự điều chỉnh để tối ưu hoá tín hiệu hồi đáp cho từng loại khí dưới các điều kiện thực tế. Chế độ tự chẩn đoán sẽ hoạt động khi mở nguồn để đảm bảo thiết bị ở trạng thái hoặt động tối. Thông tin hiệu chuẩn của 10 loại khí và hệ số quy đổi của 256 loại khí khác nhau được lưu trong bộ nhớ. Cảnh báo lưu lượng cao và thấp được lập trình theo cổng kết nối RS-485. Phần mềm cung cấp chế độ lập trình, cho phép người dùng lập trình trong 10 bước.[:en]Program, record, analyze, and control flow rates of various gases with Series DMF Digital Mass Flow Controller. Controllers are designed with straight tube sensors with restrictor flow elements to ensure laminar gas flow for accurate and repeatable results. Series DMF are unaffected by temperature and pressure variations.
Controllers can be programmed for various control functions including flow set point, totalizer, stop totalizer, totalize from preset flow, stop and preset total, auto zero, and more. Auto zero feature utilizes an automatic balancing circuit that virtually eliminates drift of zero and span. In addition, Series DMF controllers have two dry contact closures to operate pumps, valves, or other process equipment.
The Series DMF features an auto tune function to optimize control response for a specific gas under actual process conditions. Self-diagnostic tests are run at power up to ensure the controller is in optimum working condition. Calibration information for up to 10 gases and conversion factors for up to 256 different gases are stored in memory. High and low gas flow alarm limits are programmed via RS-485 interface. Software supports programmable flow modes, allowing execution of custom programming of up to ten steps.[:]